Datalogic QLM500 Instruction Manual Page 19
- Page / 161
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
RAPID CONFIGURATION
9
1
STEP 6 – X-PRESS™ CONFIGURATION
Once Matrix 410™ has calibrated image density, you can configure it for optimal code
reading relative to your application. This configuration can be performed either through the X-
PRESS™ Interface or the VisiSet™ configuration program.
Locate
1. Enter the Focus function by pressing and holding
the X-PRESS™ push button until the Focus LED
is on.
2. Release the button to enter the Focus function.
The Blue Diamonds™ turn on.
3. Select a code from your application. Position
the code at the center of the FOV (equidistant from
the Blue Diamonds™).
4. Exit the Focus function by pressing the X-
PRESS™ push button once. The Blue
Diamonds™ turn off.
READY
green
green
yellow
yellow
red
SETUP
FOCUS
TEST
LEARN
GOOD
TRIGGER
COM
STATUS
Figure 12 – X-PRESS™ Interface:
Locate Function
Setup
5. Enter the Setup function by pressing and holding
the X-PRESS™ push button until the Setup LED is
on.
6. Release the button to enter the Setup function.
The Setup LED will blink until the procedure is
completed.
The Setup procedure ends when the Image
Acquisition parameters are successfully saved in
the reader memory, the Setup LED will remain on
continuously and Matrix 410™ emits 3 high pitched
beeps.
If the calibration cannot be reached after a timeout
of about 5 (five) seconds Matrix 410™ will exit
without saving the parameters to memory, the
Setup LED will not remain on continuously but it will
just stop blinking. In this case Matrix 410™ emits a
long low pitched beep.
7. Exit the Setup function by pressing the X-
PRESS™ push button once.
READY
green
green
yellow
yellow
red
SETUP
FOCUS
TEST
LEARN
GOOD
TRIGGER
COM
STATUS
Figure 13 – X-PRESS™ Interface:
Setup Function
- MATRIX 410™ 1
- CONTENTS 3
- REFERENCES 6
- COMPLIANCE 7
- HANDLING 8
- GENERAL VIEW 10
- 1 RAPID CONFIGURATION 11
- Required Accessories 12
- STEP 2 – CONNECT THE SYSTEM 13
- (polarity insensitive) 14
- RAPID CONFIGURATION 15
- STEP 4 – FOCUS THE READER 16
- Locate Function 17
- STEP 9 – TEST MODE 27
- Host Mode Programming 30
- Alternative Layouts 30
- Code Quality Verification 30
- 2 INTRODUCTION 31
- INTRODUCTION 33
- 2.3 ID-NET™ 36
- VISISET™ 40
- Restore 41
- Replacement 42
- 2.5.1 X-PRESS™ Functions 45
- Test Mode (Function 1) 46
- Focus/Locate (Function 2) 46
- Setup (Function 3) 47
- Learn (Function 4) 47
- 2.5.2 Diagnostic Indication 47
- 2.6 MODEL DESCRIPTION 48
- 2.7 ACCESSORIES 48
- 2.7.1 Lighting System Notes 50
- 2.8 APPLICATION EXAMPLES 51
- 2.8.1 Document Handling 51
- 2.8.4 Direct Part Marking 53
- 3 INSTALLATION 57
- 3.2 MECHANICAL DIMENSIONS 58
- INSTALLATION 59
- [Ø0.32] 60
- Figure 43 - Pitch angle 62
- Figure 44 - Skew angle 62
- Figure 45 - Tilt angle 62
- CBX ELECTRICAL CONNECTIONS 63
- 4.1 POWER SUPPLY 64
- 4.2 MAIN SERIAL INTERFACE 65
- 4.2.1 RS232 Interface 66
- 4.3 ID-NET™ INTERFACE 70
- 4.3.1 ID-NET™ Cables 70
- 4.3.2 ID-NET™ Response Time 71
- 4.5 INPUTS 76
- 5.1 M16 19-PIN CONNECTOR 83
- 5.4.1 RS232 Interface 86
- 5.5 ID-NET™ INTERFACE 90
- 5.5.1 ID-NET™ Cables 90
- 5.5.2 ID-NET™ Response Time 91
- 5.8 INPUTS 97
- EXTERNAL TRIGGER 98
- Matrix 410™ 98
- INPUT DEVICE 99
- 5.9 OUTPUTS 100
- USER INTERFACE 101
- MATRIX 410™ REFERENCE MANUAL 102
- 6 TYPICAL LAYOUTS 103
- 6.2 PASS-THROUGH 106
- 6.2.1 Pass-Through on RS232 106
- 6.3 ID-NET™ 108
- BA600 ID-NET™ Out 109
- BA400 Ext. Power 109
- BA500 Trigger 109
- BA300 Service 109
- Fieldbus Interface 113
- 6.4 RS232 MASTER/SLAVE 114
- 6.5 MULTIPLEXER 115
- 6.6 ETHERNET CONNECTION 116
- TYPICAL LAYOUTS 117
- 7 READING FEATURES 118
- READING FEATURES 119
- 7.2.2 1D (Linear) Codes 120
- Line Speed 125
- 8 SOFTWARE CONFIGURATION 127
- 8.2 INSTALLING VISISET™ 128
- 8.3 STARTUP 128
- 8.3.1 VisiSet™ Options 129
- 8.4 CONFIGURATION 131
- Parameters to verify/modify: 133
- SOFTWARE CONFIGURATION 135
- 8.4.3 Calibration 138
- 8.6 STATISTICS 149
- 9 MAINTENANCE 150
- 10 TROUBLESHOOTING 151
- 11 TECHNICAL FEATURES 154
- TECHNICAL FEATURES 155
- GLOSSARY 156
- UNI EN ISO 14001 160
Related products and manuals for Bar code readers Datalogic QLM500
(2 pages)
(30 pages)
(2 pages)
(20 pages)
(2 pages)© 2020, manymanuals.com. All rights reserved. | 0.346 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals