Datalogic QLM500 Instruction Manual Page 131
- Page / 161
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
SOFTWARE CONFIGURATION
121
8
8.4 CONFIGURATION
Once connected to Matrix 410™ as described in par. 8.3, you can modify the configuration
parameters as follows:
1. Press the Calibration Tool button from the Main Menu. Matrix 410™ will download its
permanent memory configuration parameters with the default values (if it is the first time)
to VisiSet™. The Calibration Tool window will be displayed together with the Parameter
Setup window working in Interactive Mode (see par. 8.4.1 and par. 8.4.3).
2. Edit the Matrix 410™ configuration parameters according to your application
requirements.
3. Use the Calibration Tool to fine tune the reading performance. See par. 8.4.3.
4. Close the Calibration Tool window and disable the Interactive Mode by pressing the
interactive button.
5. Save the new configuration to the reader permanent memory by pressing the Send
button.
NOTE
Especially for lengthy configurations in Interactive Mode, it is always good
practice to periodically send the configuration to Permanent Memory to
avoid losing the configuration in Temporary Memory.
6. Close the Parameter Setup window and press Disconnect on the VisiSet™ menu bar
(see Figure 118) or launch Run Mode from the VisiSet™ Main menu.
Disconnect exits closing communication between Matrix 410™ and VisiSet™, and
causes Matrix 410™ to enter Run Mode. The disconnected reader serial port is now
available.
Run command does not close communication between Matrix 410™ and VisiSet™,
and causes Matrix 410™ to enter Run Mode. In this case the reader output messages
are displayed on the VisiSet™ terminal and the statistics are displayed in the
Statistics window (Statistics enabled).
- MATRIX 410™ 1
- CONTENTS 3
- REFERENCES 6
- COMPLIANCE 7
- HANDLING 8
- GENERAL VIEW 10
- 1 RAPID CONFIGURATION 11
- Required Accessories 12
- STEP 2 – CONNECT THE SYSTEM 13
- (polarity insensitive) 14
- RAPID CONFIGURATION 15
- STEP 4 – FOCUS THE READER 16
- Locate Function 17
- STEP 9 – TEST MODE 27
- Host Mode Programming 30
- Alternative Layouts 30
- Code Quality Verification 30
- 2 INTRODUCTION 31
- INTRODUCTION 33
- 2.3 ID-NET™ 36
- VISISET™ 40
- Restore 41
- Replacement 42
- 2.5.1 X-PRESS™ Functions 45
- Test Mode (Function 1) 46
- Focus/Locate (Function 2) 46
- Setup (Function 3) 47
- Learn (Function 4) 47
- 2.5.2 Diagnostic Indication 47
- 2.6 MODEL DESCRIPTION 48
- 2.7 ACCESSORIES 48
- 2.7.1 Lighting System Notes 50
- 2.8 APPLICATION EXAMPLES 51
- 2.8.1 Document Handling 51
- 2.8.4 Direct Part Marking 53
- 3 INSTALLATION 57
- 3.2 MECHANICAL DIMENSIONS 58
- INSTALLATION 59
- [Ø0.32] 60
- Figure 43 - Pitch angle 62
- Figure 44 - Skew angle 62
- Figure 45 - Tilt angle 62
- CBX ELECTRICAL CONNECTIONS 63
- 4.1 POWER SUPPLY 64
- 4.2 MAIN SERIAL INTERFACE 65
- 4.2.1 RS232 Interface 66
- 4.3 ID-NET™ INTERFACE 70
- 4.3.1 ID-NET™ Cables 70
- 4.3.2 ID-NET™ Response Time 71
- 4.5 INPUTS 76
- 5.1 M16 19-PIN CONNECTOR 83
- 5.4.1 RS232 Interface 86
- 5.5 ID-NET™ INTERFACE 90
- 5.5.1 ID-NET™ Cables 90
- 5.5.2 ID-NET™ Response Time 91
- 5.8 INPUTS 97
- EXTERNAL TRIGGER 98
- Matrix 410™ 98
- INPUT DEVICE 99
- 5.9 OUTPUTS 100
- USER INTERFACE 101
- MATRIX 410™ REFERENCE MANUAL 102
- 6 TYPICAL LAYOUTS 103
- 6.2 PASS-THROUGH 106
- 6.2.1 Pass-Through on RS232 106
- 6.3 ID-NET™ 108
- BA600 ID-NET™ Out 109
- BA400 Ext. Power 109
- BA500 Trigger 109
- BA300 Service 109
- Fieldbus Interface 113
- 6.4 RS232 MASTER/SLAVE 114
- 6.5 MULTIPLEXER 115
- 6.6 ETHERNET CONNECTION 116
- TYPICAL LAYOUTS 117
- 7 READING FEATURES 118
- READING FEATURES 119
- 7.2.2 1D (Linear) Codes 120
- Line Speed 125
- 8 SOFTWARE CONFIGURATION 127
- 8.2 INSTALLING VISISET™ 128
- 8.3 STARTUP 128
- 8.3.1 VisiSet™ Options 129
- 8.4 CONFIGURATION 131
- Parameters to verify/modify: 133
- SOFTWARE CONFIGURATION 135
- 8.4.3 Calibration 138
- 8.6 STATISTICS 149
- 9 MAINTENANCE 150
- 10 TROUBLESHOOTING 151
- 11 TECHNICAL FEATURES 154
- TECHNICAL FEATURES 155
- GLOSSARY 156
- UNI EN ISO 14001 160
Related products and manuals for Bar code readers Datalogic QLM500
(2 pages)
(30 pages)
(2 pages)
(20 pages)
(2 pages)© 2020, manymanuals.com. All rights reserved. | 0.644 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals