Datalogic PowerScan PBT9500 Specifications Page 201
- Page / 362
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
2D Global Features Enter/Exit Programming Mode
Product Reference Guide
191
PDF417 Set Length 2
This feature specifies one of the bar code lengths for PDF417 Length Con-
trol. Length 2 is the maximum label length if in Variable Length Mode, or
the second fixed length if in Fixed Lengt
h Mode. Length includes the bar
code’s check, data, and full-ASCII shift characters. The length does not
include start/stop characters. Characters can be set from 01 to 2,710 char-
acters (pad with zeroes) in increments of 01
. An
y value greater than 2,710
will be considered to be 2,710.
See page 284 for detailed instructions on setting this feature.
$CP4L2
Select PDF417 Length 2 Setting
To configure this feature, scan the ENTER/EXIT
PROGRAMMING MODE bar code above, then the bar
code at left followed by the digits from the Alphanu-
meric characters in
Appendix D, Keypad
repre-
senting your desired character(s). End by scanning
the ENTER
/EXIT bar code again.
Make a mistake? Scan the CANCEL bar code t
o
abort
and not save the entry string. You can then start
again at the beginning.
~
CANCEL
DEFAULT
Length 2 is 2,710 Characters
- PowerScan™ 9500 Family 1
- 2
- 2
- Table of Contents 3
- Product Reference Guide 5
- Contents 10
- Chapter 1 11
- Introduction 11
- References 12
- Technical Support 12
- About the Reader 13
- Table 1. LED Status 14
- Battery Safety 15
- Programming the Reader 16
- Chapter 2 17
- A. Rubber gasket 18
- B. Cable Holder 18
- C. Cover 18
- D. Connector Holder 18
- Configuring the Base Station 19
- Mounting the BC9xx0 Cradle 19
- Permanent Mounting 20
- Mounting for Portable Use 21
- Base with Mount attached 22
- 13 23
- Interface Selection 24
- 15 25
- Table 2. Available Interfaces 25
- KEYBOARD 26
- Configure Interface Settings 27
- Global Interface Features 27
- Configuring Other Features 27
- Software Version Transmission 27
- Self Test and Statistics 27
- Set Date and Time 28
- Linking the Reader 29
- Chapter 3 31
- Configuration Using Bar Codes 31
- To program features: 32
- GLOBAL INTERFACE FEATURES 33
- RS-232 ONLY INTERFACE 35
- Baud Rate 36
- Data Bits 37
- Stop Bits 37
- Handshaking Control 39
- RS-232/USB-COM INTERFACES 40
- Beep On ASCII BEL 41
- Beep On Not on File 42
- ACK NAK Error Handling 45
- Indicate Transmission Failure 45
- KEYBOARD EMULATION SETTINGS 47
- Country Mode 48
- Country Mode (continued) 49
- Send Control Characters 51
- Wedge Quiet Interval 52
- Caps Lock State 53
- USB Keyboard Speed 54
- USB Keyboard Numeric Keypad 55
- USB-OEM INTERFACE 57
- USB-OEM Device Usage 58
- Interface Options 58
- DATA FORMAT 59
- Global AIM ID 61
- AIM IDs (continued) 62
- 53 63
- Individually Set Label ID 66
- 57 67
- − 1D Symbologies 67
- 59 69
- − 2D Symbologies 70
- Case Conversion 71
- READING PARAMETERS 73
- Double Read Timeout 74
- 65 75
- LED AND BEEPER INDICATORS 76
- Good Read Beep Type 77
- Good Read Beep Frequency 77
- Good Read Beep Length 78
- Good Read Beep Volume 79
- Good Read LED Duration 80
- SCANNING FEATURES 81
- Stand Mode Indication 82
- Pick Mode 82
- Stand Mode Sensitivity 83
- Stand Illumination Control 84
- Aiming Pointer 86
- Aiming Duration Timer 86
- Green Spot Duration 87
- Partial Label Reading Control 87
- Decode Negative Image 88
- Image Capture 88
- MULTIPLE LABEL READING 89
- 1D SYMBOLOGIES 91
- DISABLE ALL SYMBOLOGIES 92
- CODE EAN/UPC 93
- UPC-A Enable/Disable 94
- Expand UPC-A to EAN-13 95
- UPC-A 2D Component 96
- UPC-E Enable/Disable 96
- UPC-E 2D Component 97
- Expand UPC-E to EAN-13 98
- Expand UPC-E to UPC-A 98
- GTIN FORMATTING 99
- EAN 13 (JAN 13) 100
- EAN-13 Flag 1 Character 101
- EAN-13 ISBN Conversion 101
- EAN-13 2D Component 102
- ISSN Enable/Disable 102
- EAN 8 (JAN 8) 103
- EAN 8 2D Component 104
- Expand EAN 8 to EAN 13 104
- UPC/EAN GLOBAL SETTINGS 105
- UPC/EAN Quiet Zones 106
- Optional Add-ons 107
- Optional Add-On Timer 108
- Enter/Exit Programming Mode 109
- 99 109
- Optional GS1-128 Add-On Timer 110
- 101 111
- Code 39 Enable/Disable 113
- Code 39 Full ASCII 115
- Code 39 Quiet Zones 116
- Code 39 Length Control 116
- Code 39 Set Length 1 117
- Code 39 Set Length 2 118
- TRIOPTIC CODE 119
- CODE 39 DANISH PPT 121
- CODE 39 LAPOSTE 122
- CODE 39 PZN 122
- CODE 128 123
- Code 128 Quiet Zones 125
- Code 128 Length Control 126
- Code 128 Set Length 1 127
- Code 128 Set Length 2 128
- GS1-128 Enable 129
- GS1-128 2D Component 129
- CODE ISBT 128 130
- ISBT 128 Concatenation Mode 131
- INTERLEAVED 2 OF 5 (I 2 OF 5) 133
- I 2 of 5 Length Control 135
- I 2 of 5 Set Length 1 136
- I 2 of 5 Set Length 2 137
- INTERLEAVED 2 OF 5 CIP HR 138
- FOLLETT 2 OF 5 138
- STANDARD 2 OF 5 139
- Variable Length: 140
- Fixed Length: 140
- Standard 2 of 5 Set Length 1 141
- Standard 2 of 5 Set Length 2 142
- INDUSTRIAL 2 OF 5 143
- 135 145
- CODE IATA 147
- Codabar Enable/Disable 148
- 139 149
- Codabar Quiet Zones 151
- Codabar Length Control 151
- Codabar Set Length 1 152
- Codabar Set Length 2 153
- ABC CODABAR 154
- 145 155
- Code 11 Enable/Disable 157
- Code 11 Length Control 158
- Code 11 Set Length 1 159
- Code 11 Set Length 2 160
- GS1 DATABAR™ OMNIDIRECTIONAL 161
- GS1 DATABAR™ EXPANDED 162
- 153 163
- 155 165
- GS1 DATABAR™ LIMITED 167
- Code 93 Enable/Disable 168
- 159 169
- Code 93 Length Control 170
- Code 93 Set Length 1 171
- Code 93 Set Length 2 172
- Code 93 Quiet Zones 173
- MSI Enable/Disable 173
- MSI Length Control 175
- MSI Set Length 1 176
- MSI Set Length 2 177
- Plessey Enable/Disable 178
- Plessey Length Control 179
- Plessey Set Length 1 180
- Plessey Set Length 2 181
- 2D SYMBOLOGIES 183
- 2D Maximum Decoding Time 184
- 2D Structured Append 185
- AZTEC CODE 186
- Aztec Code Set Length 1 187
- Aztec Code Set Length 2 188
- CHINA SENSIBLE CODE 189
- 181 191
- DATA MATRIX 192
- 183 193
- Data Matrix Length Control 194
- Data Matrix Set Length 1 194
- Data Matrix Set Length 2 195
- MAXICODE 196
- Maxicode Length Control 197
- Maxicode Set Length 1 197
- Maxicode Set Length 2 198
- PDF417 Enable / Disable 199
- PDF417 Length Control 199
- PDF417 Set Length 1 200
- PDF417 Set Length 2 201
- MICRO PDF417 202
- Micro PDF417 Length Control 203
- Micro PDF417 Set Length 1 203
- Micro PDF417 Set Length 2 204
- QR Code Enable / Disable 205
- QR Code Length Control 205
- QR Code Set Length 1 206
- MICRO QR CODE 207
- Micro QR Code Length Control 208
- Micro QR Code Set Length 1 208
- Micro QR Code Set Length 2 209
- UCC COMPOSITE 210
- UCC Optional Composite Timer 211
- POSTAL CODE SELECTION 212
- Postnet BB Control 213
- MOTION FEATURES 215
- Motion Sensitivity 216
- Motionless Timeout 216
- WIRELESS FEATURES 217
- PBT9500-Only Features 218
- PM9500-Only Features 218
- Display and Keyboard Features 219
- WIRELESS BEEPER FEATURES 220
- Beep Duration 221
- Beep Volume 222
- Disconnect Beep 222
- Docking Beep 223
- Leash Alarm 223
- Leash Alarm (continued) 224
- CONFIGURATION UPDATES 225
- BATCH FEATURES 226
- Erase Batch Memory 227
- RF Batch Mode Transmit Delay 227
- DIRECT RADIO AUTOLINK 228
- RF ADDRESS STAMPING 228
- 219 229
- Current Date 230
- Current Time 230
- Date Tx Format 231
- Time Tx Format 231
- Date-Time Separator 232
- Date-Time Transmission Order 233
- Power Off 234
- Powerdown Timeout 234
- PBT9500-ONLY FEATURES 235
- Bluetooth Security Mode 236
- Bluetooth PIN Code 236
- Select PIN Code Length 236
- Set PIN Code 237
- OTHER BLUETOOTH FEATURES 238
- 229 239
- Bluetooth HID Alt Mode 240
- Bluetooth Max Client 241
- Bluetooth Friendly Name 242
- Power Class 243
- HID Country Mode 243
- HID Country Mode (continued) 244
- PM9500-ONLY FEATURES 246
- STAR Radio Transmit Mode 247
- Changing System Speed 248
- Frequency Agility 248
- 239 249
- Table 26. Frequency Agility 249
- COMPATIBILITY WITH PM8500 250
- Return to Normal 251
- Base Address Stamping 252
- RS-485 Cradle Address 253
- RS-485 Slave Minimum Address 254
- RS-485 Slave Maximum Address 254
- RS-485 Network Working Mode 255
- RS-485 Network Baud Rate 256
- DISPLAY AND KEYBOARD FEATURES 257
- Display Off Timeout 258
- Backlight Enable 258
- Display Contrast 259
- Font Size 259
- Enable/disable buttons 260
- 251 261
- String Association Mode: 261
- 253 263
- Configure Actions for F1 264
- Configure Actions for F2 264
- 255 265
- Define Strings 267
- Set String ID 268
- Set String Header 268
- Set String Terminator 269
- Last Code Shown Timeout 270
- Display Time Stamping Mode 270
- Mode Selection 271
- Quantity Field 271
- Quantity/Code Send Mode 272
- Quantity/Code Separator 272
- Interkey Timeout 273
- Append Code 274
- Keypress Sound 275
- SHIFT Enable/Disable 276
- SHIFT key association 276
- Lower Case 277
- Set F1 Label 277
- Set F2 Label 277
- Set F3 Label 278
- Set F4 Label 278
- Set Barcode Header 279
- Set Barcode Terminator 279
- Set Key Sequence ID 280
- Set Key Sequence Header 280
- Set Key Sequence Terminator 280
- Chapter 4 281
- Request to Send 282
- Clear to Send 282
- RS-232/USB COM Parameters 283
- ACK NAK Options 284
- ACK Character 284
- NAK Character 285
- ACK NAK Timeout Value 286
- ACK NAK Retry Count 287
- Disable Character 288
- Enable Character 289
- Keyboard Interface 290
- Intercharacter Delay 291
- Intercode Delay 292
- Symbologies 293
- Set Length 2 294
- Data Editing 295
- 00 - 20 Characters (ASCII) 296
- 287 297
- Figure 9. AIM ID 297
- Label ID 298
- 289 299
- 291 301
- Table 39 302
- . Label ID Examples 302
- Character Conversion 303
- Reading Parameters 304
- Scanning Features 305
- Stand Mode Off Time 306
- Scanning Active Time 307
- Aiming Duration Time 308
- Flash On Time 309
- Flash Off Time 310
- 301 311
- Table 47 312
- . Symbology Hex Values 312
- Motion Features 313
- Wireless Features 314
- STAR Radio Protocol Timeout 315
- Bluetooth-Only Features 316
- 307 317
- Chapter 5 319
- Message Formatting 319
- Cursor Control 320
- Font Selection 320
- Clearing Display 320
- LED and Beeper Control 321
- Setting RTC 321
- 313 323
- Physical Characteristics 323
- Electrical Characteristics 323
- Performance Characteristics 324
- Depth of Field (Typical) 324
- Technical Specifications 324
- Decode Capability 325
- User Environment 325
- 315 325
- Regulatory 326
- Radio Features 326
- Imager Labeling 327
- Standard Cable Pinouts 328
- LED and Beeper Indications 329
- Error Codes 330
- Appendix B 331
- Sample Bar Codes 331
- Sample Bar Codes (continued) 332
- GS1 DataBar™ (RSS) 333
- GS1 DataBar™-14 333
- 334
- Appendix C 335
- Standard Defaults 335
- 327 337
- 329 339
- 331 341
- 333 343
- 335 345
- 337 347
- Restore Factory Configuration 348
- Appendix D 349
- Keypad (continued) 350
- Appendix E 351
- Scancode Tables 351
- Alt Mode sequence 352
- Product Reference Guide 343 353
- Product Reference Guide 345 355
- Digital Interface 356
- IBM31xx 102-key 357
- 349 359
- ASCII Chart 361
Related products and manuals for Bar code readers Datalogic PowerScan PBT9500
(20 pages)
© 2020, manymanuals.com. All rights reserved. | 0.364 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals