Datalogic QLM500 Installation Manual Page 7
- Page / 119
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
vii
Disconnect the power supply when
opening the device during maintenance or
installation to avoid exposure to hazardous
laser light.
The laser diode used in this device is
classified as a class 3B laser product
according to EN 60825-1 regulations and
as a Class IIIb laser product according to
CDRH regulations.
Any violation of the optic parts in particular
can cause radiation up to the maximum
level of the laser diode (35 mW at 630 to
680 nm).
Warning and Device Class Labels
FCC COMPLIANCE
Modifications or changes to this equipment without the expressed written approval of
Datalogic could void the authority to use the equipment.
This device complies with PART 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference which may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
POWER SUPPLY
This product is intended to be installed by Qualified Personnel only.
This accessory device is intended to be supplied by a UL Listed or CSA Certified Power Unit
with «Class 2» or LPS power source, which supplies power directly to the scanner via the 25-
pin connector.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.ctiautomation.net - Email: [email protected]
- REFERENCE MANUAL 1
- CONTENTS 3
- REFERENCES 5
- LASER SAFETY 6
- FCC COMPLIANCE 7
- POWER SUPPLY 7
- CE COMPLIANCE 8
- HANDLING 8
- GENERAL VIEW 10
- DS2400N Subzero 11
- 1 RAPID CONFIGURATION 13
- RAPID CONFIGURATION 15
- Auto Learn 18
- Auto Setup (Optional) 19
- STEP 5 – TEST MODE 25
- Host Mode Programming 26
- Alternative Layouts 26
- 2 INTRODUCTION 27
- 2.1.1 Indicators 28
- 2.2 ID-NET™ 28
- INTRODUCTION 29
- 2.3.1 Diagnostic Indication 31
- 2.3.2 X-PRESS™ Functions 32
- Test Mode Function 32
- AutoLearn Function 33
- AutoSetup Function 33
- Internal Temperature (°C) 34
- 2.5 MODEL DESCRIPTION 35
- 2.6 ACCESSORIES 36
- 3 INSTALLATION 37
- 3.2 MECHANICAL INSTALLATION 38
- 3.2.1 Mounting DS2400N 39
- Cover Screws 40
- INSTALLATION 43
- 3.3 POSITIONING 48
- CBX ELECTRICAL CONNECTIONS 49
- 4.1 POWER SUPPLY 50
- 4.2 MAIN SERIAL INTERFACE 50
- 4.2.1 RS232 Interface 51
- Multidrop Cable 54
- 4.3 ID-NET™ INTERFACE 55
- 4.3.1 ID-NET™ Cables 55
- Response Time (ms) 56
- Number of Nodes 56
- (brown) 61
- (black) (blue) 61
- PH-1 Photocell (PNP) 61
- 4.5.1 Code Verifier 64
- 4.6 OUTPUTS 64
- MAIN INTERFACE 67
- (SW SELECTABLE) 67
- DS2400N 69
- USER INTERFACE 69
- MULTIPLEXER 71
- 5.3 ID-NET™ INTERFACE 73
- 5.3.1 ID-NET™ Cables 73
- 5.5 INPUTS 79
- Vext 30 Vdc max 81
- 5.5.1 Code Verifier 82
- 5.6 OUTPUTS 82
- 5.7 USER INTERFACE - HOST 83
- 6 TYPICAL LAYOUTS 84
- 6.2 PASS-THROUGH 86
- 6.3 ID-NET™ 88
- ID-NET™ 90
- INTERFACE 93
- 6.4 RS232 MASTER/SLAVE 94
- 6.5 MULTIPLEXER LAYOUT 95
- 7 READING FEATURES 96
- Conveyor 98
- Laser Beam 98
- 7.2 LINEAR CODE READING 100
- 7.2.1 Step-Ladder Mode 100
- 7.2.2 Picket-Fence Mode 101
- 7.3 PERFORMANCE 102
- 7.3.1 Raster 102
- 7.4 READING DIAGRAMS 103
- DS2400N REFERENCE MANUAL 104
- READING FEATURES 105
- 8 MAINTENANCE 106
- 9 TROUBLESHOOTING 107
- TROUBLESHOOTING 109
- 10 TECHNICAL FEATURES 110
- TECHNICAL FEATURES 111
- GLOSSARY 112
- DECLARATION OF CONFORMITY 116
Related products and manuals for Bar code readers Datalogic QLM500
(64 pages)
(2 pages)
(63 pages)© 2020, manymanuals.com. All rights reserved. | 0.675 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals