Datalogic GRYPHON Specifications Page 327
- Page / 370
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Message Formatting
Product Reference Guide
325
Clearing Display
ESC [ 0 K
From cursor position to end of line inclusive
ESC [ 1 K
From beginning of line to cursor position (not inclusive)
ESC [ 2 K
Entire line
ESC [ 0 J
From cursor position to end of display inclusive
ESC [ 1 J
From beginning of display to cursor position (not inclu-
sive)
ESC [ 2 J
Entire display; moves cursor to upper left corner on dis-
play
LED and Beeper Control
ESC [ 0 q
Emit short High tone + short delay
ESC [ 1 q
Emit short Low tone + short delay
ESC [ 2 q
Emit long Low tone + short delay
ESC [ 3 q
Emit good read tone
ESC [ 4 q
Emit bad tx tone
ESC [ 5 q
Wait 100 ms
ESC [ 6 q
Turn on the green LED
ESC [ 7 q
Turn off the green LED
ESC [ 8 q
Turn on the green spot
ESC [ 9 q
Turn off the green spot
ESC [ 0 r
Beep for Find me function (new)
ESC [ 1 r
Power-off (new)
The LED control escape sequences are intended to activate the LEDs for short periods of time
and can be used in combination with the Beeper. The LED and Beeper will be controlled by the
system after the entire command sequence is interpreted.
Example:
ESC [ 6 q ESC [ 3 q ESC [ 7 q
Turns on the green LED, emits a good read tone, and turns off the
green LED.
ESC [ 6 q ESC [ 5 q ESC [ 7 q
Turns on the green LED for 100 ms and then turns off the green LED.
- Gryphon™ Family 1
- Table of Contents 3
- Product Reference Guide 5
- Contents 10
- Chapter 1 11
- Introduction 11
- References 12
- Technical Support 12
- About the Reader 13
- The BC40xx™ Radio Base 13
- Base Button 14
- Battery Safety 16
- Programming the Reader 18
- Chapter 2 19
- RS-232 Serial Connection 20
- 19 21
- Keyboard Wedge Connection 21
- USB Connection 21
- Configuring the Base Station 22
- Connecting the Base Station 24
- 23 25
- RF Devices 27
- Linking a BT Reader to a PC 28
- Stand Alone Layouts 29
- Interface Selection 31
- 31 33
- Configure Interface Settings 35
- Global Interface Features 35
- Configuring Other Features 35
- Software Version Transmission 35
- Restore Custom Defaults 36
- Restore Factory Configuration 36
- Replacing the Battery 37
- Chapter 3 39
- Configuration Using Barcodes 39
- GLOBAL INTERFACE FEATURES 41
- RS-232 ONLY INTERFACE 43
- Baud Rate 44
- Data Bits 45
- Stop Bits 45
- Handshaking Control 47
- RS-232/USB-COM INTERFACES 48
- Beep On ASCII BEL 49
- Beep On Not on File 50
- ACK NAK Error Handling 54
- Indicate Transmission Failure 54
- KEYBOARD INTERFACE 57
- Country Mode 58
- Country Mode — continued 59
- Caps Lock State 61
- Send Control Characters 63
- Wedge Quiet Interval 64
- USB Keyboard Speed 67
- USB Keyboard Numeric Keypad 68
- USB-OEM INTERFACE 69
- USB-OEM Device Usage 70
- Interface Options 70
- IBM 46XX INTERFACE 71
- 46xx Number of Host Resets 72
- WAND EMULATION INTERFACE 75
- Wand Signal Speed 76
- Wand Polarity 76
- Wand Idle State 77
- Transmit Noise 77
- Label Symbology Conversion 78
- DATA FORMAT 79
- GS1-128 AIM ID 82
- Label ID: Pre-loaded Sets 83
- Label ID Control 84
- Label ID Symbology Selection 85
- Case Conversion 92
- READING PARAMETERS 93
- Double Read Timeout 94
- Label Gone Timeout 95
- Sleep Mode Timeout 96
- LED AND BEEPER INDICATORS 98
- Good Read Beep Type 99
- Good Read Beep Frequency 99
- Good Read Beep Length 100
- Good Read Beep Volume 101
- Good Read LED Duration 102
- SCANNING FEATURES 103
- Stand Mode Triggered Timeout 104
- Stand Detection 105
- Scanning Active Time 106
- Stand Mode Sensitivity 106
- Flash On Time 107
- Flash Off Time 107
- Green Spot Duration 108
- CODE SELECTION 109
- DISABLE ALL SYMBOLOGIES 110
- CODE EAN/UPC 111
- UPC-A Enable/Disable 112
- Expand UPC-A to EAN-13 113
- UPC-A Minimum Reads 114
- UPC-E Enable/Disable 115
- Expand UPC-E to EAN-13 116
- Expand UPC-E to UPC-A 116
- UPC-E Minimum Reads 117
- GTIN FORMATTING 118
- EAN 13 (JAN 13) 119
- EAN-13 Flag 1 Character 120
- EAN-13 ISBN Conversion 120
- EAN 13 Minimum Reads 121
- ISSN Enable/Disable 122
- EAN 8 (JAN 8) 123
- Expand EAN 8 to EAN 13 124
- EAN 8 Minimum Reads 124
- UPC/EAN GLOBAL SETTINGS 125
- UPC/EAN Correlation 126
- UPC/EAN Price Weight Check 126
- In-Store Minimum Reads 127
- Optional Add-ons 128
- Optional Add-On Timer 129
- Optional Add-On Timer — cont 130
- Optional GS1-128 Add-On Timer 132
- P2 Add-Ons Minimum Reads 135
- P5 Add-Ons Minimum Reads 136
- GS1-128 Add-Ons Minimum Reads 137
- Code 39 Enable/Disable 138
- Code 39 Full ASCII 140
- Code 39 Quiet Zones 141
- Code 39 Minimum Reads 142
- Code 39 Decoding Level 143
- Code 39 Length Control 144
- Code 39 Set Length 1 145
- Code 39 Set Length 2 146
- Code 39 Interdigit Ratio 147
- Code 39 Interdigit Ratio = 6 148
- Code 39 Interdigit Ratio = 7 148
- Code 39 Interdigit Ratio = 8 148
- Code 39 Interdigit Ratio = 9 148
- Code 39 Interdigit Ratio = 10 148
- Code 39 Character Correlation 149
- Code 39 Stitching 149
- Code 32 Enable/Disable 150
- Code 39 CIP Enable/Disable 152
- CODE 128 153
- Code 128 Quiet Zones 156
- Code 128 Minimum Reads 157
- Code 128 Decoding Level 158
- Code 128 Length Control 159
- Code 128 Set Length 1 160
- Code 128 Set Length 2 161
- Code 128 Stitching 162
- GS1-128 Enable 163
- CODE ISBT 128 164
- ISBT 128 Concatenation Mode 165
- CODABLOCK F 167
- Codablock F AIM Check 168
- Codablock F Length Control 168
- Codablock F Set Length 1 169
- Codablock F Set Length 2 170
- INTERLEAVED 2 OF 5 (I 2 OF 5) 171
- I 2 of 5 Minimum Reads 173
- 2 of 5 Decoding Level 174
- I 2 of 5 Length Control 175
- I 2 of 5 Set Length 1 176
- I 2 of 5 Set Length 2 177
- I 2 of 5 Stitching 178
- FOLLETT 2 OF 5 179
- INTERLEAVED 2 OF 5 CIP HR 179
- STANDARD 2 OF 5 180
- Standard 2 of 5 Minimum Reads 181
- Standard 2 of 5 Set Length 1 183
- Standard 2 of 5 Set Length 2 184
- Standard 2 of 5 Stitching 185
- INDUSTRIAL 2 OF 5 186
- Industrial 2 of 5 Stitching 190
- CODE IATA 192
- DATALOGIC 2 OF 5 193
- "2 of 5 Decoding 194
- Level" on page 172 194
- Datalogic 2 of 5 Set Length 1 196
- Datalogic 2 of 5 Set Length 2 197
- Datalogic 2 of 5 Stitching 198
- Codabar Enable/Disable 199
- Codabar Quiet Zones 202
- Codabar Minimum Reads 203
- Codabar Decoding Level 204
- Codabar Length Control 205
- Codabar Set Length 1 206
- Codabar Set Length 2 207
- Codabar Interdigit Ratio 208
- Codabar Interdigit Ratio = 6 209
- Codabar Interdigit Ratio = 7 209
- Codabar Interdigit Ratio = 8 209
- Codabar Interdigit Ratio = 9 209
- Codabar Interdigit Ratio = 10 209
- Codabar Character Correlation 210
- Codabar Stitching 210
- ABC CODABAR 211
- Concatenation Mode 212
- Code 11 Enable/Disable 214
- Code 11 Minimum Reads 215
- Code 11 Length Control 216
- Code 11 Set Length 1 217
- Code 11 Set Length 2 218
- Code 11 Interdigit Ratio 219
- Code 11 Interdigit Ratio = 6 220
- Code 11 Interdigit Ratio = 7 220
- Code 11 Interdigit Ratio = 8 220
- Code 11 Interdigit Ratio = 9 220
- Code 11 Interdigit Ratio = 10 220
- Code 11 Decoding Level 221
- Code 11 Character Correlation 222
- Code 11 Stitching 222
- GS1 DATABAR™ OMNIDIRECTIONAL 223
- GS1 DATABAR™ EXPANDED 225
- GS1 DATABAR™ LIMITED 229
- Code 93 Enable/Disable 231
- Code 93 Length Control 232
- Code 93 Set Length 1 233
- Code 93 Set Length 2 234
- Code 93 Minimum Reads 235
- Code 93 Decoding Level 236
- Code 93 Quiet Zones 237
- Code 93 Stitching 238
- Code 93 Character Correlation 238
- MSI Enable/Disable 239
- MSI Length Control 240
- MSI Set Length 1 241
- MSI Set Length 2 242
- MSI Minimum Reads 243
- MSI Decoding Level 244
- Plessey Enable/Disable 245
- Plessey Length Control 247
- Plessey Set Length 1 248
- Plessey Set Length 2 249
- Plessey Minimum Reads 250
- Plessey Decoding Level 251
- Plessey Stitching 252
- Plessey Character Correlation 252
- Code 4 Enable/Disable 253
- Code 5 Enable/Disable 254
- Code 4 and 5 Decoding Level 256
- Chapter 4 259
- Wireless Features 259
- ENTER/EXIT PROGRAMMING MODE 260
- WIRELESS BEEPER FEATURES 261
- Beep Duration 262
- Beep Volume 263
- Disconnect Beep 263
- Base Station Beep 264
- Leash Alarm 264
- Leash Alarm — cont 265
- CONFIGURATION UPDATES 266
- Automatic Flash Update 267
- Request Flash Update 268
- Powerdown Timeout 268
- Powerdown Timeout — continued 269
- BATCH FEATURES 270
- Erase Batch Memory 271
- RF Batch Mode Transmit Delay 271
- DIRECT RADIO AUTOLINK 272
- RF ADDRESS STAMPING 272
- 00 = No Delimiter Character 273
- Features for Star Models Only 274
- STAR Radio Transmit Mode 275
- DISPLAY FEATURES 276
- Backlight 277
- Display Mode 277
- Display Timeout 278
- Display Timeout - cont 279
- Keypad Select 280
- Bluetooth-Only Features 281
- BT SECURITY FEATURES 282
- BT Pin Code 283
- Select PIN Code Length 283
- Set PIN Code 283
- BT HID FEATURES 284
- BT HID Send Unkown ASCII Char 285
- OTHER BT FEATURES 286
- BT Poll Rate (continued) 287
- Other BT Features 288
- Chapter 5 289
- Laser Features 289
- Laser Scan Angle 290
- Laser Idle Mode 290
- Bi-Directional Read Decoding 291
- Always On Scan Mode Timeout 292
- Chapter 6 293
- RS-232/USB COM Parameters 294
- ACK NAK Options 295
- ACK Character 295
- NAK Character 296
- ACK NAK Timeout Value 297
- ACK NAK Retry Count 298
- Disable Character 299
- Enable Character 300
- Keyboard Interface 301
- Intercharacter Delay 302
- Intercode Delay 303
- Symbologies 304
- Set Length 2 305
- Data Editing 306
- Global Prefix/Suffix 307
- Global AIM ID 308
- Label ID 309
- 309 311
- Character Conversion 313
- Reading Parameters 314
- Scanning Features 316
- Display Settings 320
- RF Features 320
- 319 321
- STAR Radio Protocol Timeout 322
- BT-Only Features 323
- Chapter 7 325
- Message Formatting 325
- Cursor Control 326
- Font Selection 326
- Clearing Display 327
- LED and Beeper Control 327
- Appendix A 329
- Technical Specifications 329
- Standard Cable Pinouts 332
- LED and Beeper Indications 333
- Error Codes 334
- Appendix B 337
- Standard Defaults 337
- Appendix C 349
- Sample Bar Codes 349
- Sample Bar Codes — continued 350
- GS1 DataBar™ (RSS) 351
- GS1 DataBar™-14 351
- Appendix D 353
- HID Variable PIN Code 354
- Appendix E 357
- Scancode Tables 357
- Product Reference Guide 357 359
- Product Reference Guide 359 361
- Digital Interface 362
- IBM31xx 102-key 363
- ASCII Chart 369
Related products and manuals for Bar code readers Datalogic GRYPHON
(2 pages)
Bar code readers Datalogic F732 User Manual
(39 pages)
(39 pages)
(50 pages)© 2020, manymanuals.com. All rights reserved. | 0.144 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals