Datalogic Magellan 1100i Instruction Manual Page 18
- Page / 208
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
General Features
10
Magellan
TM
1100i
Label Gone Timeout
This feature sets the time after the last label segment is seen before the scanner prepares for
a new label.
START / END
PROGRAMMING BARCODES
Sets the label gone timeout duration using hex
values from 000 to 255 in increments of ten milliseconds
(10ms or 0.01 seconds). To configure this feature, scan the “START/END” barcode above to place the unit in
Programming Mode, then the “Set Linear Label Gone Timeout,” followed by the three digits (zero padded)
from the Alphanumeric table in
Appendix C, Alpha-Numeric Pad representing the desired time value. Exit pro-
gramming mode by scanning the “START/END” barcode again.
DEFAULT SETTING FOR THIS FEA
TURE: 320 milliseconds (032)
Set Linear Label Gone Timeout
Productivity Index Reporting (PIR)
When PIR is enabled, label quality data is appended to decoded data before being presented
to the POS. The PIR feature allows the scanner to provide information to an external com-
puter, indicating how easy the
label was to read.
NOTE
START / END
PROGRAMMING BARCODES
Disable
DEFAULT
Enable
This value-added feature is a factory-pro-
grammed option. Contact your dealer for
inf
ormation about upgrading your system
to include this advanced capability.
- Magellan 1
- Table of Contents 3
- Product Reference Guide iii 5
- Getting Started 9
- Connecting the Scanner 10
- Programming 11
- LED and Beeper Indicators 12
- Error Codes 13
- General Features 15
- Aztec or Composite label 17
- Label Gone Timeout 18
- Sleep Mode 19
- Sleep Mode — cont 20
- ERI Timeout 22
- Good Read: When to Indicate 23
- Good Read Beep Control 24
- Good Read Beep Frequency 24
- Good Read Beep Length 25
- Good Read Beep Volume 26
- Green Spot 26
- Aiming Pointer Settings 27
- Scanning Features 28
- Target Mode Linger Time 29
- Wake Up Intensity 30
- Image Capture 31
- Image Compression 32
- Image Size 32
- Image Brightness 33
- Image Contrast 33
- Cell Phone Mode 34
- Cell Phone in Target Mode 37
- Interface Related Features 39
- Mappings 40
- Interface Selection 41
- Interface Selection — cont 42
- Interface Features 43
- Interface Features — cont 44
- RS-232 Interface Features 45
- Hardware Flow Control 47
- Intercharacter Delay 48
- Intercharacter Delay — cont 49
- Software Flow Control 49
- Host Echo Quiet Interval 50
- Signal Voltage: Normal/TTL 51
- Beep on ASCII BEL 52
- Beep on Not on File 52
- ACK NAK Options 53
- ACK Character 54
- NAK Character 54
- Retry on ACK NAK Timeout 55
- ACK NAK Timeout Value 55
- ACK NAK Retry Count 56
- ACK NAK Error Handling 57
- USB-OEM Interface Features 58
- USB Keyboard 60
- Keyboard Wedge — cont 61
- USB COM Interface Set-up 66
- Data Editing 67
- Global Prefix/Suffix 68
- Global Prefix/Suffix — cont 69
- Label ID 71
- Label ID — cont 72
- Case Conversion 78
- Character Conversion 79
- UPC-A — continued 82
- Disable/Enable UPC-E 85
- Check Digit Transmission 85
- UPC-E — continued 86
- Expand UPC/EAN to GTIN 88
- Disable/Enable EAN-13 89
- EAN-13 — continued 90
- Disable/Enable EAN-8 92
- EAN-8 — continued 93
- EAN Two-Label 94
- EAN Two-Label — continued 95
- Price Weight Check Digit 100
- Contact Customer Support for 101
- Add-ons — continued 102
- UCC/EAN 128 Emulation 105
- Minimum Reads 106
- GS1-128 Emulation 107
- Length Control 108
- Coupon Read Control 111
- GS1 DataBar Limited 112
- Disable/Enable Code 39 114
- Check Character Calculation 114
- Check Character Transmit 115
- Start/Stop Characters 115
- Code 39 Full ASCII 116
- Code 39 — continued 117
- Quiet Zones 118
- Code 32 Italian Pharmacode 120
- Code 128 122
- Code 128 — continued 123
- Interleaved 2 of 5 127
- Check Digit Transmit 128
- Symbologies 130
- Interleaved 2 of 5 Stitching 131
- Disable/Enable Codabar 133
- Check Character Verification 133
- Codabar — continued 135
- Start/Stop Character Match 138
- Codabar Stitching 138
- Disable/Enable Code 93 140
- Code 93 — continued 141
- MSI/Plessey 144
- MSI/Plessey — continued 145
- Standard 2 of 5 150
- Standard 2 of 5 — continued 151
- 2D Symbologies 157
- Disable/Enable PDF 417 158
- PDF 417 — continued 159
- Micro PDF 417 161
- Micro PDF 417 — continued 162
- Datamatrix 164
- Datamatrix — continued 165
- Disable/Enable QR Code 167
- QR Code — continued 168
- Maxicode 170
- Maxicode — continued 171
- Disable/Enable Aztec 173
- Aztec — continued 174
- Composite Labels 176
- Advanced Decoding Features 179
- Inverse Label Reading 180
- Chapter A 181
- Product Specifications 181
- Physical Properties 182
- Electrical Parameters 182
- Environmental Parameters 182
- Other Parameters 182
- Cable Pinouts 183
- USB, USB Keyboard 184
- & USB COM 184
- Keyboard Wedge 184
- Alpha-Numeric Pad 185
- Appendix D 187
- Default Settings 187
- Interface Default Exceptions 188
- RS-232 Wincor/Nixdorf 189
- Keyboards 190
- Appendix E 191
- Chapter F 199
- Host Commands 199
- Chapter G 201
- Sample Symbols 201
- 1D Symbol Samples — continued 202
- 2D Sample Symbols 203
- Composite Sample Symbols 204
- 197 205
- ASCII Chart 207
- Datalogic ADC, Inc 208
Related products and manuals for Bar code readers Datalogic Magellan 1100i
(2 pages)
(50 pages)
Bar code readers Datalogic DS4800 User Manual
(100 pages)
(100 pages)
© 2020, manymanuals.com. All rights reserved. | 5.197 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals